By:
Printer
The first way to Reset Printer Canon iP series in general is to press and hold the RESUME button for several seconds (Printer in living conditions), release the Resume button and the printer will return to normal, in this situation the actual condition is not 100% normal printer as still Cartridge Status empty or not displayed or Disable although full of ink condition.
This means that it's time Canon printer to reset. Ink Absorber is our term for the full discharge ink. Download Canon Printer Resetter just below .. !!!
1 Turn off the printer, then unplug the power cable
2 While pressing the ON button plug the power cable
3 Still keep pressing the ON button, press the Resume button 2x
4 Remove the two buttons.
5. In this stage the printer is reset and for temporary total reset, run Resetter apps that you have downloaded.
6 Wait a moment until the program detects the presence of a printer
7 Prepare 2 sheets of paper put in Printers
8 Click the "Play" on the software Resetter (first print process which results in figures)
9 Continue with the click of a button "EEPROM CLEAR" followed by clicking "EEPROM" In this process the printer will print the result in some formatting codes that tell Printer Reset was successful or not
10 Turn off the printer Canon iP by pressing the Power button, Done.
The number of the (Reset button) pressing LED
Stop Reset button is Command Service Mode
0 time Green Power off
1 time Orange Service pattern print
2 times Green EEPROM print
3 times Orange EEPROM reset
4 times Green Waste ink counter reset
It means ....
1 Connect the power, Press Off (make sure it's Off)
2 Press together and hold (Power button and the Stop / Reset)
3 If the light is already a flame. still hold the power button continuously press the Stop / Reset much as 2x (double-click)
4 Well now off the power button. Where the printer is now in Service mode position. Now just wait for a command from you.
5. See list above ya .. !!!! If you want to reset Waste Ink Counter, then you must press the Stop / Reset 4 times, make sure the lighting color Green.
6 Turn off the printer by pressing the power button off. (do not forget to continue to be separated from the power source, wait 10 seconds and then plug it into a power source ..)
7 Success and good luck .. !!!
It For Your Printer Resetting .. Most potent, Be sure to read the manual first ... !!! (unplug the power cord. then press the power plug into a power source.) Here printer under normal circumstances, then use the software below, blinking will disappear .. !!!
2. If your computer is detected in other types of printers, for example: IP 1800 or IP 1700 then you should use this software:
Do not forget to manually reset only after that you are using this software.
Remove the Power, Press and hold the power button, plug it into a power source, a new off power button.
3. If when printing is blinking, then you press and hold the reset button for 5-10 seconds.
4. I give tips to print the manual, press the reset button rather quickly.
5. To Reset, make sure you select ASA, Do not use IPTOOL. Because often chaotic, and the average entry europe not asia region .. !!
1. Turn off the printer and then unplug the usb
2. At the position of the printer is off, press the Start / Stop button on selected models the Resume / Cancel resistant, not released.
3. Then press the power button, wait until the lights flash and the green Led
4. Then Remove button Start / Stop or Resume / Cancel but still hold the Power button and do not release yes ...
5. Then press the Start / Stop or Resume / Cancel 2 times (double click), the LCD will appear later in writing 0 (Zero)
6. Now Power off button. then plug in to the CPU, will be in detect a new printer .. !!! This is normal do not worry ..
7. Above is the code to enter into the manual mode .. !!! Further resetting the software we use, where resetting software can not be done if it is not in the manual .. !!!
B. Reset Permanent use Software
Download the first software of here, then run the file service_tool 1050.exe
Step-by-Steps
1 Printers do not forget given paper, Minimum 2 pieces .. !!!
2 Make sure the USB port ...
3 See Clear Ink Counter, there is a Play button. Click Play when the process is complete, the printer can print directly.
4 Then click on the button when the process is complete Platen direct printer can print again .. !!!
5. if it is finished turn off the printer and turn your printer will be normal .. Again .. !!!
1 Manual Reset, Remove the power, press the power button, hold it, then plug in the electric source. Now position the printer in the service mode.
2 Then in the software by using the following
Canon Pixma iP1300, iP1700
This means that it's time Canon printer to reset. Ink Absorber is our term for the full discharge ink. Download Canon Printer Resetter just below .. !!!
Complete Printer Resetter And Drivers (Canon)
Canon Service Tools (Software Resetters Canon Printers)
* iPTool support Canon iP1200, iP1300, iP1600, iP1700, iP1800, iP2200, iP2500
* MPTool support Canon MP150, MP160, MP170, MP180, MP450, MP460
* Canon i320
* Canon iP1100, iP2500
* Canon iP1500
* Canon Pixma iP1200, iP1600, ip2200
* Canon Pixma iP1300, iP1700
* Canon Pixma iP1800
* Canon Pixma Ip 1980
Led Error code for Canon IP1300, IP1700, IP1200, IP1880, IP1980
4x orange 1x green
Problem printer absorber full, Full exhaust Ink
Solution: Reset the printer with the above software. how in the manual first then use the software reset
5x orange 1x green
Problem: Black or Color cartridge trouble. There head is problematic
Note: There are many causes, Chipset error, or a dirty connector can also already time to ask sister.
Solution: press resume 10-30 minutes, if not solved the mean time requested updated.
7x orange 1x green
Problem: Black or Color cartridge trouble. There head is problematic
Note: There are many causes, Chipset error, or a dirty connector can also already time to ask sister.
Solution: press resume 10-30 minutes, if not solved the time to ask replaced with a new one
8x orange 1x green
Problem printer absorber full (Waste Ink Pad Full)
Solution: Reset the printer with the above software. how in the manual first then use the software reset
My experience troubleshooting Canon MP145
In order fully normally try to follow steps - these steps:1 Turn off the printer, then unplug the power cable
2 While pressing the ON button plug the power cable
3 Still keep pressing the ON button, press the Resume button 2x
4 Remove the two buttons.
5. In this stage the printer is reset and for temporary total reset, run Resetter apps that you have downloaded.
6 Wait a moment until the program detects the presence of a printer
7 Prepare 2 sheets of paper put in Printers
8 Click the "Play" on the software Resetter (first print process which results in figures)
9 Continue with the click of a button "EEPROM CLEAR" followed by clicking "EEPROM" In this process the printer will print the result in some formatting codes that tell Printer Reset was successful or not
10 Turn off the printer Canon iP by pressing the Power button, Done.
The number of the (Reset button) pressing LED
Stop Reset button is Command Service Mode
0 time Green Power off
1 time Orange Service pattern print
2 times Green EEPROM print
3 times Orange EEPROM reset
4 times Green Waste ink counter reset
It means ....
1 Connect the power, Press Off (make sure it's Off)
2 Press together and hold (Power button and the Stop / Reset)
3 If the light is already a flame. still hold the power button continuously press the Stop / Reset much as 2x (double-click)
4 Well now off the power button. Where the printer is now in Service mode position. Now just wait for a command from you.
5. See list above ya .. !!!! If you want to reset Waste Ink Counter, then you must press the Stop / Reset 4 times, make sure the lighting color Green.
6 Turn off the printer by pressing the power button off. (do not forget to continue to be separated from the power source, wait 10 seconds and then plug it into a power source ..)
7 Success and good luck .. !!!
Canon iP1880
It you use for the reset Ink Level course, so that the ink is full plasticity, can create a printer reset. but I do not recommend .. !!iPTool support Canon iP1200, iP1300, iP1600, iP1700, iP1800, iP2200, iP2500
It For Your Printer Resetting .. Most potent, Be sure to read the manual first ... !!! (unplug the power cord. then press the power plug into a power source.) Here printer under normal circumstances, then use the software below, blinking will disappear .. !!!
Canon Pixma iP1800
Canon iP1200
1. Make sure that the driver in the clear. then plug your printer ... see your OS detects what type of printer .. !!! If detect iP1200 printer is indeed true then it means you have done a reset. Make sure the printer is loaded drivers .. !!!2. If your computer is detected in other types of printers, for example: IP 1800 or IP 1700 then you should use this software:
Canon Pixma iP1200, iP1600, ip2200
Do not forget to manually reset only after that you are using this software.
Remove the Power, Press and hold the power button, plug it into a power source, a new off power button.
3. If when printing is blinking, then you press and hold the reset button for 5-10 seconds.
4. I give tips to print the manual, press the reset button rather quickly.
4 times resumes Head Cleaning
5 a test print resumes Head
5. To Reset, make sure you select ASA, Do not use IPTOOL. Because often chaotic, and the average entry europe not asia region .. !!
Canon MP198, MP258, MP276, MP496, MP558, MP568, and MP648
A. Go to Service Mode.1. Turn off the printer and then unplug the usb
2. At the position of the printer is off, press the Start / Stop button on selected models the Resume / Cancel resistant, not released.
3. Then press the power button, wait until the lights flash and the green Led
4. Then Remove button Start / Stop or Resume / Cancel but still hold the Power button and do not release yes ...
5. Then press the Start / Stop or Resume / Cancel 2 times (double click), the LCD will appear later in writing 0 (Zero)
6. Now Power off button. then plug in to the CPU, will be in detect a new printer .. !!! This is normal do not worry ..
7. Above is the code to enter into the manual mode .. !!! Further resetting the software we use, where resetting software can not be done if it is not in the manual .. !!!
B. Reset Permanent use Software
Download the first software of here, then run the file service_tool 1050.exe
Step-by-Steps
1 Printers do not forget given paper, Minimum 2 pieces .. !!!
2 Make sure the USB port ...
3 See Clear Ink Counter, there is a Play button. Click Play when the process is complete, the printer can print directly.
4 Then click on the button when the process is complete Platen direct printer can print again .. !!!
5. if it is finished turn off the printer and turn your printer will be normal .. Again .. !!!
Canon IP1300, IP1700
Do it manually first, then use the software1 Manual Reset, Remove the power, press the power button, hold it, then plug in the electric source. Now position the printer in the service mode.
2 Then in the software by using the following
Canon Pixma iP1300, iP1700